• tricor-01
  • tricor-02
  • tricor-03
  • tricor-04

Table of Mechanical Properties (ASTM) for Titanium Plate & Sheet

   Bend Test
grade tensile strength,min yield strength, 0.2% offset elongation In 2 in. or 50 mm, Min, % under 0.070 in (1.8 mm) in Thickness 0.070 to 0.187 in. (1.8 to 4.75 Mm) in Thickness
min max
ksi mpa ksi mpa ksi mpa

1

35

240

20

138

45

310

24

1.5t

2t

2

50

345

40

275

65

450

20

2t

2.5t

2h

58

400

40

275

65

450

20

2t

2t

3

65

450

55

380

80

550

18

2t

2.5t

4

80

550

70

483

95

655

15

2.5t

3t

5

130

895

120

828

...

...

10vii

4.5t

5t

6

120

828

115

793

...

...

10vii

4t

4.5t

7

50

345

40

275

65

450

20

2t

2.5t

7h

58

400

40

275

65

450

20

2t

2t

9

90

620

70

483

...

...

15viii

2.5t

3t

11

35

240

20

138

45

310

24

1.5t

2t

12

70

483

50

345

...

...

18

2t

2.5t

13

40

275

25

170

...

...

24

1.5t

2t

14

60

410

40

275

...

...

20

2t

2.5t

15

70

483

55

380

...

...

18

2t

2.5t

16

50

345

40

275

65

450

20

2t

2.5t

16h

58

400

40

275

65

450

20

2t

2t

17

35

240

25

170

45

310

24

1.5t

2t

18

90

620

70

483

...

...

15viii

2.5t

3t

19ii

115

793

110

759

...

...

15

3t

3t

20ii

115

793

110

759

...

...

15

3t

3t

21ii

115

793

110

759

...

...

15

3t

3t

23ii

120

828

110

759

...

...

10

4.5t

5t

24

130

895

120

828

...

...

10

4.5t

5t

25

130

895

120

828

...

...

10

4.5t

5t

26

50

345

40

275

65

450

20

2t

2.5t

27

35

240

25

170

45

310

24

2t

4t

28

90

620

70

483

...

...

15

2.5t

3t

29

120

828

110

759

...

...

10

4.5t

5t

30

50

345

40

275

65

450

20

2t

2.5t

31

65

450

55

380

80

550

18

2t

2.5t

32

100

689

85

586

...

...

10vii

3.5t

4.5t

33

50

345

40

275

65

450

20

2t

2.5t

34

65

450

55

380

80

550

18

2t

2.5t

35

130

895

120

828

 

 

5

8t

8t

36

65

450

60

410

95

655

10

4.5t

5t

37

50

345

31

215

65

450

20

2t

2.5t

38

130

895

115

794

 

 

10

4t

4.5t

above Mechanical limits apply to tests taken both longitudinal and Transverse to the direction of rolling.  Mechanical Properties for conditions other than annealed or plate thickness Over 1 inch may be established by agreement between the Manufacturer and the purchaser."T" equals the Thickness of the bend test specimen.  Bend tests are not Applicable to material over 0.187 in (4.75 min) in thickness.

ii) Properties for solution treated condition. Material is most Often purchased and supplied in the solution treated condition. Aged material may be available, but is subject to negotiation Between purchaser and supplier.

vii) Elongation for grades 5, 6 and 32 on materials under 0.025 inch In thickness subject to negotiation manufacturer and purchaser.

viii) Elongation for continuous rolled and annealed (strip product From coil) for grade 9 and grade 18 shall be 12% minimum in the Longitudinal direction and 8% minimum in the transverse Direction.

** While this information has been compiled with care, it is for convenience and for reference only and we assume no liability for any decisions based on the content therein.  it shall be your responsibility to ensure that any information in this document or on our website meets your specific requirements. **

Resources
Top